Program Ecolite HO Receiver with an OT 200 Transmitter

Program Ecolite HO Receiver with an OT 200 Transmitter

Below is a guide to programming your pet's receiver using an OT 200 transmitter. 

Video Link - https://youtu.be/JtTWcrV7I-g

Programming:


1. Note the number that you see on the LED display of your transmitter (Mounted on the wall). Pro Tip - Also, you might find it easier to access the buttons when you pop the front cover off


2. Unplug the power cord from the transmitter (left-hand bottom corner) and, holding both black buttons down on the transmitter at the same time, plug the power cord back in. Display shows  “10"

3. You are always going to start with the bottom button (edit) and end with the bottom button (to set).

Frequency (10)
4. Press the bottom button once - display goes to 11 - press the top button two times - display goes to 13 - press the bottom button to set - display goes to 20

Warning Time (20)
5. Press the bottom button once - display goes to 21 - press the top button once - display goes to 22 - press the bottom button once to set - display goes to 30

Options:

21 - No warning

22 - 1/2 second warning

23 - 1 second warning

24 - 2 second warning


Stimulation Level (30)
6. Press the bottom button once - display goes to 31 - press the top button 3 times - display goes to 34 - press the bottom button to set - display goes to 40

Options:

31 - Low

32 - Medium-Low

33 - Medium-High

34 - High

38 - No Shock

39 - Puppy Mode Engaged (See 80 setting)


Progressive Duration (40)
7. Press the bottom button once - display goes to 41 - press the bottom button to set - display goes to 50

Battery Saving (50)
8. Press the bottom button - display goes to 51 - press the top button once - display goes to 54 - press the bottom button to set - display goes to 60

Modulation (60)
9. Press the bottom button - display goes to 61 - press the bottom button to set - display goes to 70

Stopper (70)
10. Press the bottom button - display goes to 71 -  press the bottom button to set - display goes to 80 

Options:

71 - Stopper disabled

72 - 2 seconds

73 - 4 seconds

74 - 6 seconds


Puppy Training Mode (80) - This category might not be available on older equipment
11. Press the bottom button - display goes to 81 (older equipment - 80 may not appear) - press the bottom button to set - display goes to 90

Options:

This has settings from 1-9, a more gentle way of introducing a puppy to the system. This setting is only triggered if setting 39 has been set.


Review Settings (90)
12. Category 90 is a review mode, telling you the settings that you have entered.  The process is the same. Press the bottom button and the display will go to 13; repeatedly touch the top button and it will cycle through the settings showing you: 13,22,34,41,52,61,71,81, (99) - these settings will vary depending on what you chose from the options above.

Pairing (99)

13. 99 means the transmitter is ready to send the settings to the collar. Push the bottom button and the 99 will flash; while the 99 is flashing, hold your receiver over top the black buttons on the transmitter until you see the red light on your receiver (collar) come on - when the red light is on, press the bottom button on the transmitter and it will start transmitting the programming to the collar. You will see and hear a series of beeps and flashes come out of the collar. Once the beeping and flashing have stopped, that means the collar is programmed. If, for some reason, the red light does not come on right away, press the bottom button again to get the 99 flashing and repeat the process.                                                                                      

14. You can now wait a few minutes, and the transmitter will go back to the original number that was on your display when you started.  To speed this reset up, you can unplug the transmitter and then plug it back in, and the display will show you the original number. If , for some reason, the display light does not come on, press the bottom button again to get the 99 flashing and repeat the process 


15. Test your receiver by holding it up to the transmitter, and it will beep; this beeping will indicate that the reprogramming has been successful. As a double check, you can walk out to the boundary and make sure that the collar beeps at the edge of the signal field.


Please feel free to call us at 403-226-2717 if you have any questions.

    • Related Articles

    • Program Ecolite HO Receiver with an OT 300 Transmitter

      Below is a guide to programming your pet's receiver using an OT 300 transmitter. Video Link - https://youtu.be/p3QTTmYXI0A Programming: 1. Note the number that you see on the LED display of your transmitter. 2. Put the OT 300 transmitter into ...

    • Program Ecolite HO Receiver with an OT 200 Transmitter

      Below is a guide to programming your pet's receiver using an OT 200 transmitter. Video Link - https://youtu.be/JtTWcrV7I-g Programming: 1. Note the number that you see on the LED display of your transmitter (Mounted on the wall). Pro Tip - Also, you ...

    • Program Ecolite HO Receiver with an OT 200 Transmitter

      Below is a guide to programming your pet's receiver using an OT 200 transmitter. Video Link - https://youtu.be/JtTWcrV7I-g Programming: 1. Note the number that you see on the LED display of your transmitter (Mounted on the wall). Pro Tip - Also, you ...

    • Program Ultra Tuff Receiver with an OT 300 Transmitter

      Below is a guide to programming your pet's receiver using an OT 300 transmitter. Video Link - https://youtu.be/94wKLqkjIQg Programming: 1. Note the number that you see on the LED display of your transmitter. 2. Put the OT 300 transmitter into ...

    • Program Ultra Tuff Receiver with an OT 300 Transmitter

      Below is a guide to programming your pet's receiver using an OT 300 transmitter. Video Link - https://youtu.be/94wKLqkjIQg Programming: 1. Note the number that you see on the LED display of your transmitter. 2. Put the OT 300 transmitter into ...